A Novel Predictive Voltage Control Technique for a Grid Connected Five Phase Permanent Magnet Synchronous Generator
(1) Hussein Mahmoud Mail (1) Electrical Engineering Department, Faculty of Engineering, Damietta University, Damietta 34517, Egypt. 2) b Electrical Engineering Department, Faculty of Engineering, Minia University, Minia 61111, Egypt)
(2) Mohamed A. Mohamed Mail (Minia University, Egypt)
(3) Ahmed A. Hassan Mail (Minia University, Egypt)
(4) * Mahmoud A. Mossa Mail (Minia University, Egypt)
*corresponding author

Abstract


This study focuses on developing an effective control strategy to enhance the dynamics of a wind turbine grid-connected five-phase permanent magnet synchronous generator (PMSG). To visualize the superior performance of the newly proposed controller, the generator's performance is evaluated with another traditional predictive control scheme: predictive torque control (PTC). However, the vector control principle is applied to the GSC converter. The PTC has limitations such as significant ripple, substantial load commutation, and the inclusion of a weighting element in its cost functions. The proposed predictive methodology aims to overcome limitations, uses a simple cost function, and doesn't require weighting elements to address concerns about stability errors. Comparing the proposed predictive voltage controller (PVC) to the PTC, the findings show that the suggested PVC has many benefits, including faster dynamic response, a simpler control structure, fewer ripples, reduced current harmonics, low computation burdens, and robustness, so the generated power affects system efficiency, leading to improved power quality and reduced switching losses, enhancing power converters efficiency and their switches lifespan, this fact is verified mathematically as the total harmonic distortion (THD) has reduced to 1.346% average percentage for the proposed controller. However, the THD of the PTC is 3.05%. In addition, the study examines the incorporation of pitch angle control (PAC) and maximum power point tracking (MPPT). These controls restrict the consumption of wind energy when the generator speed surpasses its rated speed and optimize the extraction of wind energy during periods of low wind availability. In summary, the proposed PVC-enhanced control system reveals superior performance in dynamic response, control simplicity, current quality, and computational efficiency compared to other methods.

Keywords


Five-Phase PMSG; Wind Turbine; MPPT; Vector Control; Predictive Control

   

DOI

https://doi.org/10.31763/ijrcs.v4i3.1386 		      

Article metrics

10.31763/ijrcs.v4i3.1386 Abstract views : 1034 | PDF views : 204

   

Cite

How to cite item
   

Full Text

Download

References


[1] S. Mathur, H. Waswani, D. Singh, and R. Ranjan, “Alternative fuels for agriculture sustainability: Carbon footprint and economic feasibility,” AgriEngineering, vol. 4, no. 4, pp. 993-1015, 2022, https://doi.org/10.3390/agriengineering4040063.

[2] F. J. Medaiyese et al., “Energy Transition with Dimethyl Ether (An Alternative Fuel to Diesel) to minimise the Environmental Impact,” 84th EAGE Annual Conference & Exhibition, 2023, https://clok.uclan.ac.uk/47006/9/Revised%20paper%20number%20330.pdf.

[3] J. Wolf et al., “9.04 - Environmental Issues for Offshore Renewable Energy,” Comprehensive Renewable Energy (Second Edition), vol. 9, pp. 25-59, 2022, https://doi.org/10.1016/B978-0-12-819727-1.00036-4.

[4] M. Nurunnabi, N. K. Roy, E. Hossain and H. R. Pota, “Size Optimization and Sensitivity Analysis of Hybrid Wind/PV Micro-Grids- A Case Study for Bangladesh,” IEEE Access, vol. 7, pp. 150120-150140, 2019, https://doi.org/10.1109/ACCESS.2019.2945937.

[5] X. Xie, Y. Zhang, K. Meng, Z. Y. Dong and J. Liu, “Emergency control strategy for power systems with renewables considering a utility-scale energy storage transient,” CSEE Journal of Power and Energy Systems, vol. 7, no. 5, pp. 986-995, 2021, https://doi.org/10.17775/CSEEJPES.2019.02320.

[6] P. Sadorsky, “Wind energy for sustainable development: Driving factors and future outlook,” Journal of Cleaner Production, vol. 289, p. 125779, 2021, https://doi.org/10.1016/j.jclepro.2020.125779.

[7] S. Pira, “The Importance of Renewable Energies with Emphasize on Wind Power,” International Journal of Engineering Research & Technology, vol. 9, no. 6, pp. 812-822, 2020, https://www.ijert.org/the-importance-of-renewable-energies-with-emphasize-on-wind-power.

[8] A. Eicke, L. Eicke, and M. Hafner, “Wind Power Generation,” The Palgrave Handbook of International Energy Economics, pp. 171-182, 2022, https://doi.org/10.1007/978-3-030-86884-0_10.

[9] A. I. Beksultanova, P. M. Dzhankhotova, and S. K. Shardan, “Renewable and alternative energy sources. Green energy,” IOP Conference Series: Earth and Environmental Science, vol. 1045, no. 1, p. 012134, 2022, https://doi.org/10.1088/1755-1315/1045/1/012134.

[10] S. Kumar and K. Rathore, “Renewable energy for sustainable development goal of clean and affordable energy,” International Journal of Materials Manufacturing and Sustainable Technologies, vol. 2, no. 1, pp. 1-15, 2023, https://typeset.io/pdf/renewable-energy-for-sustainable-development-goal-of-clean-2xwmb24p.pdf.

[11] W. Yang and J. Yang, “Advantage of variable-speed pumped storage plants for mitigating wind power variations: Integrated modelling and performance assessment,” Applied Energy, vol. 237, pp. 720-732, 2019, https://doi.org/10.1016/j.apenergy.2018.12.090.

[12] O. J. Tola, E. A. Umoh, E. A. Yahaya, O. E. Osinowo, “Permanent magnet synchronous generator connected to a grid via a high speed sliding mode control,” International Journal of Robotics and Control Systems, vol. 2, no. 2, pp. 379-395, 2022, https://doi.org/10.31763/ijrcs.v2i2.701.

[13] O. Apata and D. T. O. Oyedokun, “Impact Of Statcom On Voltage Stability Of Fixed Speed Wind Farms,” 2020 IEEE PES/IAS PowerAfrica, pp. 1-5, 2020, https://doi.org/10.1109/PowerAfrica49420.2020.9219989.

[14] H. T, C. G and S. D, “SCIG Based Wind Energy Conversion System Fed DC Micro Grid Using DTC,” 2023 International Conference on Recent Trends in Electronics and Communication (ICRTEC), pp. 1-5, 2023, https://doi.org/10.1109/ICRTEC56977.2023.10111866.

[15] K. Teng, Z. Lu, J. Long, Y. Wang and A. P. Roskilly, “Voltage Build-Up Analysis of Self-Excited Induction Generator With Multi-Timescale Reduced-Order Model,” IEEE Access, vol. 7, pp. 48003-48012, 2019, https://doi.org/10.1109/ACCESS.2019.2902977.

[16] M. A. Mossa, A. Saad Al-Sumaiti, T. Duc Do and A. A. Zaki Diab, “Cost-Effective Predictive Flux Control for a Sensorless Doubly Fed Induction Generator,” IEEE Access, vol. 7, pp. 172606-172627, 2019, https://doi.org/10.1109/ACCESS.2019.2951361.

[17] H. Singh and M. Singh, “Investigations On The Control Strategy of Rotor Side Converter In Doubly Fed Induction Generator,” 2021 International Conference on Communication, Control and Information Sciences (ICCISc), pp. 1-6, 2021, https://doi.org/10.1109/ICCISc52257.2021.9484874.

[18] K. Tamvada and S. Umashankar, “Fuzzy rotor side converter control of doubly Fed induction generator,” Artificial Intelligence and Evolutionary Computations in Engineering Systems, pp. 657-663, 2018, https://doi.org/10.1007/978-981-10-7868-2_62.

[19] M. A. Mossa, T. Duc Do, A. Saad Al-Sumaiti, N. V. Quynh and A. A. Z. Diab, “Effective Model Predictive Voltage Control for a Sensorless Doubly Fed Induction Generator,” IEEE Canadian Journal of Electrical and Computer Engineering, vol. 44, no. 1, pp. 50-64, 2021, https://doi.org/10.1109/ICJECE.2020.3018495.

[20] S. Purushothaman, D. Samiappan, M. Kamalkannan, N. Joseph, and R. Murugavel, “LVRT Enhancement of DFIG-based WECS using SVPWM-based Inverter Control,” Recent Advances in Electrical & Electronic Engineering, vol. 17, no. 4, pp. 345-357, 2024, http://dx.doi.org/10.2174/2352096516666230606103013.

[21] I. R. de Oliveira, F. L. Tofoli, and V. F. Mendes, “Thermal analysis of power converters for DFIG-based wind energy conversion systems during voltage sags,” Energies, vol. 15, no. 9, p. 3152, 2022, https://doi.org/10.3390/en15093152.

[22] L. Pan and C. Shao, “Wind energy conversion systems analysis of PMSG on offshore wind turbine using improved SMC and Extended State Observer,” Renewable Energy, vol. 161, pp. 149-161, 2020, https://doi.org/10.1016/j.renene.2020.06.057.

[23] M. A. Mossa, O. Gam, N. Bianchi and N. V. Quynh, “Enhanced Control and Power Management for a Renewable Energy-Based Water Pumping System,” IEEE Access, vol. 10, pp. 36028-36056, 2022, https://doi.org/10.1109/ACCESS.2022.3163530.

[24] M. M. Islam and D. Chowdhury, “Advanced and comprehensive control methods in wind energy systems,” CRC Press, pp. 191-224, 2021, https://doi.org/10.1201/9781003058472-6.

[25] M. K. K. Prince, M. T. Arif, A. Gargoom, A. M. T. Oo and M. E. Haque, “Modeling, Parameter Measurement, and Control of PMSG-based Grid-connected Wind Energy Conversion System,” Journal of Modern Power Systems and Clean Energy, vol. 9, no. 5, pp. 1054-1065, 2021, https://doi.org/10.35833/MPCE.2020.000601.

[26] A. M. I. Mohamad, M. Fakhari Moghaddam Arani and Y. A. -R. I. Mohamed, “Investigation of Impacts of Wind Source Dynamics and Stability Options in DC Power Systems With Wind Energy Conversion Systems,” IEEE Access, vol. 8, pp. 18270-18283, 2020, https://doi.org/10.1109/ACCESS.2020.2966363.

[27] K. Palanimuthu, G. Mayilsamy, S. R. Lee, S. Y. Jung, and Y. H. Joo, “Comparative analysis of maximum power extraction and control methods between PMSG and PMVG-based wind turbine systems,” International Journal of Electrical Power & Energy Systems, vol. 143, p. 108475, 2022, https://doi.org/10.1016/j.ijepes.2022.108475.

[28] E. C. Navarrete, M. Trejo Perea, J. C. Jáuregui Correa, R. V. Carrillo Serrano and G. J. R. Moreno, “Expert Control Systems Implemented in a Pitch Control of Wind Turbine: A Review,” IEEE Access, vol. 7, pp. 13241-13259, 2019, https://doi.org/10.1109/ACCESS.2019.2892728.

[29] S. Foti, A. Testa, S. De Caro, L. D. Tornello, G. Scelba, and M. Cacciato, “Multi-level multi-input converter for hybrid renewable energy generators,” Energies, vol. 14, no. 6, p. 1764, 2021, https://doi.org/10.3390/en14061764.

[30] Y. Gang, G. Yichang, Z. Lidan, L. Dongdong and L. Xing, “Multi-Phase Permanent Magnet Synchronous Generator Variable Speed Constant Frequency Offshore Wind System Based on Modular Multilevel Converter,” 2019 IEEE Innovative Smart Grid Technologies - Asia (ISGT Asia), pp. 2127-2132, 2019, https://doi.org/10.1109/ISGT-Asia.2019.8881506.

[31] M. A. Mossa, N. Vu Quynh, H. Echeikh, and T. D. Do, “Deadbeat‐Based Model Predictive Voltage Control for a Sensorless Five‐Phase Induction Motor Drive,” Mathematical Problems in EngineeringMathematical Problems in Engineering, vol. 2020, no. 1, pp. 1-30, 2020, https://doi.org/10.1155/2020/4164526.

[32] M. A. Mossa, H. Echeikh, A. A. Z. Diab, H. Haes Alhelou, and P. Siano, “Comparative study of hysteresis controller, resonant controller and direct torque control of five-phase IM under open-phase fault operation,” Energies, vol. 14, no. 5, p. 1317, 2021, https://doi.org/10.3390/en14051317.

[33] G. Li, J. Hu, Y. Li and J. Zhu, “An Improved Model Predictive Direct Torque Control Strategy for Reducing Harmonic Currents and Torque Ripples of Five-Phase Permanent Magnet Synchronous Motors,” IEEE Transactions on Industrial Electronics, vol. 66, no. 8, pp. 5820-5829, 2019, https://doi.org/10.1109/TIE.2018.2870359.

[34] A. Khamitov and E. L. Severson, “Design of Multi-Phase Combined Windings for Bearingless Machines,” IEEE Transactions on Industry Applications, vol. 59, no. 3, pp. 3243-3255, 2023, https://doi.org/10.1109/TIA.2023.3243595.

[35] N. Mohamed, D. Abdelkader, and B. Y. Mohammed, “Modeling of Two Five-Phase Induction Machines Connected in Series with an Open Phase,” Advanced Computational Techniques for Renewable Energy Systems, pp. 555-564, 2022, https://doi.org/10.1007/978-3-031-21216-1_57.

[36] O. Stiscia, M. Biasion, S. Rubino, S. Vaschetto, A. Tenconi and A. Cavagnino, “Iron Losses and Parameters Investigation of Multi-Three-Phase Induction Motors in Normal and Open-Phase Fault Conditions,” 2022 International Conference on Electrical Machines (ICEM), pp. 793-799, 2022, https://doi.org/10.1109/ICEM51905.2022.9910784.

[37] J. Kellner and M. Praženica, “Research into the possibility of improving the efficiency and torque ripple of a drive with a five-phase induction motor by Changing the control in a fault state,” 2022 International Symposium on Power Electronics, Electrical Drives, Automation and Motion (SPEEDAM), pp. 663-670, 2022, https://doi.org/10.1109/SPEEDAM53979.2022.9842124.

[38] H. T. Canseven and A. Ünsal, “Performance Improvement of a Five-Phase PMSM Drive Under Open Circuit Stator Faults,” 2021 5th International Symposium on Multidisciplinary Studies and Innovative Technologies (ISMSIT), pp. 561-565, 2021, https://doi.org/10.1109/ISMSIT52890.2021.9604537.

[39] R. Basak, G. Bhuvaneswari and R. R. Pillai, “Low-Voltage Ride-Through of a Synchronous Generator-Based Variable Speed Grid-Interfaced Wind Energy Conversion System,” IEEE Transactions on Industry Applications, vol. 56, no. 1, pp. 752-762, 2020, https://doi.org/10.1109/TIA.2019.2946125.

[40] S. Rhaili, A. Abbou, S. Marhraoui, N. El Hichami and A. V. Hemeyine, “Robustness investigation of Vector Control of Five-phase PMSG based Variable-Speed Wind Turbine under faulty condition,” 2018 Renewable Energies, Power Systems & Green Inclusive Economy (REPS-GIE), pp. 1-6, 2018, https://doi.org/10.1109/REPSGIE.2018.8488809.

[41] M. R. M. Hassan, M. Mossa, and G. M. Dousoky, “Dynamic Performance Analysis of An Electric Vehicle System Using Different Control Algorithms,” Journal of Advanced Engineering Trends, vol. 43, no. 1, pp. 151-162, 2024, https://dx.doi.org/10.21608/jaet.2022.138420.1202.

[42] C. S. T. Dong, H. H. Le, and H. H. Vo, “Field oriented controlled permanent magnet synchronous motor drive for an electric vehicle,” International Journal of Power Electronics and Drive Systems, vol. 14, no. 3, pp. 1374-1381, 2023, http://doi.org/10.11591/ijpeds.v14.i3.pp1374-1381.

[43] A. Benevieri, L. Carbone, S. Cosso, F. Gallione, D. Gnudi and S. Hussain, “Field Oriented Control System Modeling for a New Flywheel Energy Storage System,” 2023 13th International Symposium on Advanced Topics in Electrical Engineering (ATEE), pp. 1-7, 2023, https://doi.org/10.1109/ATEE58038.2023.10108380.

[44] B. G. Ranjolkar, S. Angadi and A. B. Raju, “Field Oriented Control of Synchronous Reluctance Machine for Electric Vehicle Applications,” 2022 IEEE North Karnataka Subsection Flagship International Conference (NKCon), pp. 1-5, 2022, https://doi.org/10.1109/NKCon56289.2022.10126850.

[45] A. Dieng, J. C. Le Claire, A. B. Mboup, M. F. Benkhoris and M. Aït-Ahmed, “An improved torque control strategy of “five-phase PMSG-PWM rectifier” set for marine current turbine applications,” 2019 IEEE 13th International Conference on Compatibility, Power Electronics and Power Engineering (CPE-POWERENG), pp. 1-6, 2019, https://doi.org/10.1109/CPE.2019.8862372.

[46] P. Colli and D. Manini, “Sliding mode control for a generalization of the Caginalp phase-field system,” Applied Mathematics & Optimization, vol. 84, pp. 1395-1433, 2021, https://doi.org/10.1007/s00245-020-09682-3.

[47] A. Ma’arif, M. A. M. Vera, M. S. Mahmoud, E. Umoh, A. J. Abougarair, and S. N. Rahmadhia, “Sliding Mode Control Design for Magnetic Levitation System,” Journal of Robotics and Control, vol. 3, no. 6, pp. 848-853, 2022, https://doi.org/10.18196/jrc.v3i6.12389.

[48] R. Rahmatullah, A. Ak, and N. F. O. Serteller, “SMC controller design for DC motor speed control applications and performance comparison with FLC, PID and PI controllers,” Intelligent Sustainable Systems, vol. 579, pp. 607-617, 2023, https://doi.org/10.1007/978-981-19-7663-6_57.

[49] O. Dange, N. Patil, S. Gadgune and R. M. Linus, “Speed Control of BLDC Motor using Integral Sliding Mode Controller,” 2023 Third International Conference on Advances in Electrical, Computing, Communication and Sustainable Technologies (ICAECT), pp. 1-4, 2023, https://doi.org/10.1109/ICAECT57570.2023.10117574.

[50] S. Chen, G. Wu, and C. Yu, “Robust fractional‐order integral terminal sliding mode control with adaptive uncertainty observation for a VCM‐driven X–Y motion stage,” IET Electric Power Applications, vol. 17, no. 2, pp. 161-180, 2023, https://doi.org/10.1049/elp2.12252.

[51] A. Rajeevan and L. P. P. S, “Higher Order Integral Sliding Mode Controller for a Robotic Manipulator,” IECON 2022 – 48th Annual Conference of the IEEE Industrial Electronics Society, pp. 1-6, 2022, https://doi.org/10.1109/IECON49645.2022.9968410.

[52] M. R. M. Hassan, M. A. Mossa, and G. M. Dousoky, “Evaluation of electric dynamic performance of an electric vehicle system using different control techniques,” Electronics, vol. 10, no. 21, p. 2586, 2021, https://doi.org/10.3390/electronics10212586.

[53] V. Yaramasu and B. Wu, “Model predictive control of wind energy conversion systems,” John Wiley & Sons, 2016, https://doi.org/10.1002/9781119082989.

[54] A. A. Ahmed, A. Bakeer, H. H. Alhelou, P. Siano, and M. A. Mossa, “A new modulated finite control set-model predictive control of quasi-Z-source inverter for PMSM drives,” Electronics, vol. 10, no. 22, p. 2814, 2021, https://doi.org/10.3390/electronics10222814.

[55] Z. Zhang, Z. Li, M. P. Kazmierkowski, J. Rodríguez and R. Kennel, “Robust Predictive Control of Three-Level NPC Back-to-Back Power Converter PMSG Wind Turbine Systems With Revised Predictions,” IEEE Transactions on Power Electronics, vol. 33, no. 11, pp. 9588-9598, 2018, https://doi.org/10.1109/TPEL.2018.2796093.

[56] Z. Zhang, H. Fang, F. Gao, J. Rodríguez and R. Kennel, “Multiple-Vector Model Predictive Power Control for Grid-Tied Wind Turbine System With Enhanced Steady-State Control Performance,” IEEE Transactions on Industrial Electronics, vol. 64, no. 8, pp. 6287-6298, 2017, https://doi.org/10.1109/TIE.2017.2682000.

[57] M. A. Mossa and S. Bolognani, “Predictive Power Control for a Linearized Doubly Fed Induction Generator Model,” 2019 21st International Middle East Power Systems Conference (MEPCON), pp. 250-257, 2019, https://doi.org/10.1109/MEPCON47431.2019.9008085.

[58] I. Jlassi and A. J. Marques Cardoso, “Enhanced and Computationally Efficient Model Predictive Flux and Power Control of PMSG Drives for Wind Turbine Applications,” IEEE Transactions on Industrial Electronics, vol. 68, no. 8, pp. 6574-6583, 2021, https://doi.org/10.1109/TIE.2020.3005095.

[59] P. R. U. Guazzelli, W. C. de Andrade Pereira, C. M. R. de Oliveira, A. G. de Castro and M. L. de Aguiar, “Weighting Factors Optimization of Predictive Torque Control of Induction Motor by Multiobjective Genetic Algorithm,” IEEE Transactions on Power Electronics, vol. 34, no. 7, pp. 6628-6638, 2019, https://doi.org/10.1109/TPEL.2018.2834304.

[60] M. A. Mossa, O. Gam, and N. Bianchi, “Dynamic performance enhancement of a renewable energy system for grid connection and stand-alone operation with battery storage,” Energies, vol. 15, no. 3, p. 1002, 2022, https://doi.org/10.3390/en15031002.

[61] M. E. Emna, K. Adel, and M. F. Mimouni, “The wind energy conversion system using PMSG controlled by vector control and SMC strategies,” International journal of renewable energy research, vol. 3, no. 1, pp. 41-50, 2013, https://dergipark.org.tr/en/pub/ijrer/issue/16080/168268.

[62] L. Shengquan, L. Juan, T. Yongwei, S. Yanqiu, and C. Wei, “Model-based model predictive control for a direct-driven permanent magnet synchronous generator with internal and external disturbances,” Transactions of the Institute of Measurement and Control, vol. 42, no. 3, pp. 586-597, 2020, https://doi.org/10.1177/0142331219878574.

[63] G. Mayilsamy et al., “A Review of State Estimation Techniques for Grid-Connected PMSG-Based Wind Turbine Systems,” Energies, vol. 16, no. 2, p. 634, 2023, https://doi.org/10.3390/en16020634.

[64] Z. Jamal Mohammed, S. Enad Mohammed and M. Obaid Mustafa, “Improving the Performance of Pitch Angle Control of Variable Speed Wind Energy Conversion Systems Using Fractional PI Controller,” 2022 Iraqi International Conference on Communication and Information Technologies (IICCIT), pp. 209-215, 2022, https://doi.org/10.1109/IICCIT55816.2022.10010639.

[65] A. Mansouri, I. e. Myasse, A. E. Magri, R. Lajouad and F. Giri, “Nonlinear Control of Five-Phase PMSG Wind Turbine connected to Vienna Type Rectifier Using SVPWM,” 2023 3rd International Conference on Innovative Research in Applied Science, Engineering and Technology (IRASET), pp. 1-6, 2023, https://doi.org/10.1109/IRASET57153.2023.10152932.

[66] M. A. Mossa and S. Bolognani, “Effective model predictive direct torque control for an induction motor drive,” 2016 International Symposium on Power Electronics, Electrical Drives, Automation and Motion (SPEEDAM), pp. 746-754, 2016, https://doi.org/10.1109/SPEEDAM.2016.7525814.

[67] D. Zheng, G. Lu, Y. Yang, Q. Zhang and P. Zhang, “The Online Stator Winding Insulation Monitoring for PMSG-PWM rectifier System under Various Working Conditions,” IECON 2021 – 47th Annual Conference of the IEEE Industrial Electronics Society, pp. 1-6, 2021, https://doi.org/10.1109/IECON48115.2021.9589591.

[68] M. A. Mossa and S. Bolognani, “Effective model predictive direct torque control for an induction motor drive,” 2016 International Symposium on Power Electronics, Electrical Drives, Automation and Motion (SPEEDAM), pp. 746-754, 2016, https://doi.org/10.1109/SPEEDAM.2016.7525814.

[69] M. R. Hazari, E. Jahan, M. A. Mannan, and N. Das, “Transient stability enhancement of a grid-connected large-scale PV system using fuzzy logic controller,” Electronics, vol. 10, no. 19, p. 2437, 2021, https://doi.org/10.3390/electronics10192437.

[70] A. Memon, M. W. Mustafa, M. N. Aman, A. Hafeez, and M. Ullah, “Improving transient behavior of a brushless doubly fed induction generator through reactive current control of grid-side converter,” Electronics, vol. 10, no. 12, p. 1413, 2021, https://doi.org/10.3390/electronics10121413.

[71] X. Kong, X. Liu, L. Ma and K. Y. Lee, “Hierarchical Distributed Model Predictive Control of Standalone Wind/Solar/Battery Power System,” IEEE Transactions on Systems, Man, and Cybernetics: Systems, vol. 49, no. 8, pp. 1570-1581, 2019, https://doi.org/10.1109/TSMC.2019.2897646.

[72] I. Jlassi and A. J. Marques Cardoso, “Open‐circuit fault‐tolerant operation of permanent magnet synchronous generator drives for wind turbine systems using a computationally efficient model predictive current control,” IET Electric Power Applications, vol. 15, no. 7, pp. 837-846, 2021, https://doi.org/10.1049/elp2.12062.


Refbacks

  • There are currently no refbacks.


Copyright (c) 2024 Hussein Mahmoud, Mohamed A. Mohamed, Ahmed A. Hassan, Mahmoud A. Mossa

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

 

About the JournalJournal PoliciesAuthor Information

International Journal of Robotics and Control Systems
e-ISSN: 2775-2658
Website: https://pubs2.ascee.org/index.php/IJRCS
Email: ijrcs@ascee.org
Organized by: Association for Scientific Computing Electronics and Engineering (ASCEE), Peneliti Teknologi Teknik Indonesia, Department of Electrical Engineering, Universitas Ahmad Dahlan and Kuliah Teknik Elektro
Published by: Association for Scientific Computing Electronics and Engineering (ASCEE)
Office: Jalan Janti, Karangjambe 130B, Banguntapan, Bantul, Daerah Istimewa Yogyakarta, Indonesia