(University of Souk Ahras, Algeria)(2) Farid Berrezzek
(University of Souk Ahras, Algeria)(3) Khaled Khelil
(University of Souk Ahras, Algeria)*corresponding author
AbstractThis paper proposes a cascaded Takagi-Sugeno Model Predictive Controller (TS-MPC) for a Doubly-fed Induction Generator (DFIG) based Wind Power Conversion System (WPCS) to maximize power extraction, maintain zero stator reactive power, and enhance power quality. For this purpose, the Takagi-Sugeno Fuzzy Logic Control (TS-FLC) is arranged in a sequential configuration with the Finite Control-Set Model Predictive Control (FCS-MPC) strategy to enhance the overall performance of the wind power system. The introduced control technique, which is applied to govern the Rotor Side Converter (RSC) of the DFIG, consists of two cascaded control loops for achieving Maximum Power Point Tracking (MPPT). The innermost control loop is implemented to regulate the d-q axis rotor currents using FCS-MPC strategy. Meanwhile the outermost control loop is employed to regulate the DFIG’s rotational speed pursuant to the Tip Speed Ratio MPPT (TSR-MPPT) control framework using the TS-FLC, thus improving the predictive accuracy and control effectiveness. To validate the performance of the devised control scheme, a numerical simulation of a 1.5MW DFIG based WPCS was conducted using MATLAB/Simulink software. The simulation results demonstrate that the proposed cascaded TS-MPC not only outperforms the cascaded PI-MPC in terms of superior adaptability to nonlinearities and varying wind conditions—thanks to the inherent flexibility of TS-FLC—but also in various performance metrics, including response time, steady-state error, and total harmonic distortion (THD).Furthermore, while FCS-MPC approaches are often criticized for computational complexity, the TS-FLC structure enhances real-time feasibility by reducing computational overhead compared to conventional FLC methods. These findings reinforce the practical viability of TS-MPC for large-scale wind energy applications and indicate the effectiveness of the proposed control scheme.
KeywordsDoubly-Fed Induction Generator; Takagi-Sugeno Fuzzy Logic Controller; Finite Control Set Model Predictive Controller; Maximum Power Point Tracking; Rotor Side Converter; Output Power Quality
|
DOIhttps://doi.org/10.31763/ijrcs.v5i2.1786 |
Article metrics10.31763/ijrcs.v5i2.1786 Abstract views : 10 | PDF views : 8 |
Cite |
Full Text Download
|
References
[1] I. Yaichi, A. Semmah, and P. Wira, “Control of doubly fed induction generator with maximum power point tracking for variable speed wind energy conversion systems,” Periodica Polytechnica Electrical Engineering and Computer Science, vol. 64, no. 1, pp. 87–96, 2020, https://doi.org/10.3311/PPee.14166.
[2] J. Wang, D. Bo, Q. Miao, Z. Li, X. Wu, and D. Lv, “Maximum power point tracking control for a doubly fed induction generator wind energy conversion system based on multivariable adaptive super-twisting approach,” International Journal of Electrical Power & Energy Systems, vol. 124, p. 106347, 2021, https://doi.org/10.1016/j.ijepes.2020.106347.
[3] A. Kasbi and A. Rahali, “Performance optimization of doubly-fed induction generator (DFIG) equipped variable-speed wind energy turbines by using three-level converter with adaptive fuzzy PI control system,” Materialstoday Proceedings, vol. 47, pp. 2648-2656, 2021, https://doi.org/10.1016/j.matpr.2021.05.406.
[4] N. Bounar, S. Labdai, and A. Boulkroune, “PSO–GSA based fuzzy sliding mode controller for DFIG-based wind turbine,” ISA Transactions, vol. 85, pp. 177-188, 2019, https://doi.org/10.1016/j.isatra.2018.10.020.
[5] B. Desalegn, D. Gebeyehu, and B. Tamrat, “Smoothing electric power production with DFIG-based wind energy conversion technology by employing hybrid controller model,” Energy Reports, vol. 10, pp. 38–60, 2023, https://doi.org/10.1016/j.egyr.2023.06.004.
[6] R. Mittal, K. S. Sandhu, and D. K. Jain, “An Overview of Some Important Issues Related to Wind Energy Conversion System (WECS),” International Journal of Environmental Science and Development, vol. 1, no. 4, pp. 351–363, 2010, https://doi.org/10.7763/IJESD.2010.V1.69.
[7] S. Karad and R. Thakur, “Recent Trends of Control Strategies for Doubly Fed Induction Generator Based Wind Turbine Systems: A Comparative Review,” Archives of Computational Methods in Engineering, vol. 28, no. 1, pp. 15–29, 2021, https://doi.org/10.1007/s11831-019-09367-3.
[8] S. A. Nasef, A. A. Hassan, H. T. Elsayed, M. B. Zahran, M. K. El-Shaer, and A. Y. Abdelaziz, “Optimal Tuning of a New Multi-input Multi-output Fuzzy Controller for Doubly Fed Induction Generator-Based Wind Energy Conversion System,” Arabian Journal for Science and Engineering, vol. 47, no. 3, pp. 3001–3021, 2022, https://doi.org/10.1007/s13369-021-05946-4.
[9] A. G. Abo-Khalil, “Synchronization of DFIG output voltage to utility grid in wind power system,” Renewable Energy, vol. 44, pp. 193–198, 2012, https://doi.org/10.1016/j.renene.2012.01.009.
[10] G. S. Kaloi, J. Wang, and M. H. Baloch, “Active and reactive power control of the doubly fed induction generator based on wind energy conversion system,” Energy Reports, vol. 2, pp. 194-200, 2016, https://doi.org/10.1016/j.egyr.2016.08.001.
[11] O. Zamzoum, Y. El Mourabit, M. Errouha, A. Derouich, and A. El Ghzizal, “Power control of variable speed wind turbine based on doubly fed induction generator using indirect field-oriented control with fuzzy logic controllers for performance optimization,” Energy Science & Engineering, vol. 6, no. 5, pp. 408-423, 2018, https://doi.org/10.1002/ese3.215.
[12] A. Tamaarat and A. Benakcha, “Performance of PI controller for control of active and reactive power in DFIG operating in a grid-connected variable speed wind energy conversion system,” Frontiers in Energy, vol. 8, no. 3, pp. 371–378, 2014, https://doi.org/10.1007/s11708-014-0318-6.
[13] B. Wadawa, Y. Errami, A. Obbadi, S. Sahnoun, E. Chetouani, and M. Aoutoul, “Comparative application of the self-adaptive fuzzy-PI controller for a wind energy conversion system connected to the power grid and based on DFIG,” International Journal of Dynamics and Control, vol. 10, no. 6, pp. 2151–2173, 2022, https://doi.org/10.1007/s40435-022-00952-2.
[14] A. M. Kassem, K. M. Hasaneen, and A. M. Yousef, “Dynamic modeling and robust power control of DFIG driven by wind turbine at infinite grid,” International Journal of Electrical Power & Energy Systems, vol. 44, no. 1, pp. 375–382, 2013, https://doi.org/10.1016/j.ijepes.2011.06.038.
[15] A. Kasbi and A. Rahali, “Adaptive FOPI controller based on the fuzzy supervisory for wind power conversion system equipped by a doubly fed induction generator,” International Transactions on Electrical Energy Systems, vol. 31, no. 8, pp. 1-29, 2021, https://doi.org/10.1002/2050-7038.12923.
[16] Y. E. Fadili, Y. Berrada, and I. Boumhidi, “Novel control strategy for the global model of wind turbine,” International Journal of Electrical and Computer Engineering (IJECE), vol. 14, no. 1, pp. 258–267, 2024, http://doi.org/10.11591/ijece.v14i1.pp258-267.
[17] B. Kelkoul and A. Boumediene, “Stability analysis and study between classical sliding mode control (SMC) and super twisting algorithm (STA) for doubly fed induction generator (DFIG) under wind turbine,” Energy, vol. 214, p. 118871, 2021, https://doi.org/10.1016/j.energy.2020.118871.
[18] S. Kadi, H. Benbouhenni, E. Abdelkarim, K. Imarazene, and E. M. Berkouk, “Implementation of third-order sliding mode for power control and maximum power point tracking in DFIG-based wind energy systems,” Energy Reports, vol. 10, pp. 3561-3579, 2023, https://doi.org/10.1016/j.egyr.2023.09.187.
[19] H. Chojaa, A. Derouich, S. E. Chehaidia, O. Zamzoum, M. Taoussi, and H. Elouatouat, “Integral sliding mode control for DFIG based WECS with MPPT based on artificial neural network under a real wind profile,” Energy Reports, vol. 7, pp. 4809–4824, 2021, https://doi.org/10.1016/j.egyr.2021.07.066.
[20] C. Hamid et al., “Performance improvement of the variable speed wind turbine driving a dfig using nonlinear control strategies,” International Journal of Power Electronics and Drive Systems, vol. 12, no. 4, pp. 2470–2482, 2021, http://doi.org/10.11591/ijpeds.v12.i4.pp2470-2482.
[21] R. Rouabhi, R. Abdessemed, A. Chouder, and A. Djerioui, “Hybrid backstepping control of a doubly fed wind energy induction generator,” Hybrid backstepping control of a doubly fed wind energy induction generator, vol. 11, no. 1, pp. 367–376, 2015, https://num.univ-msila.dz/DWE/public/attachements/2022/10/25/mediterranenpdf-374gdabb1666674875.pdf.
[22] R. K. Kumar and J. Choudhary, “Current source converter-based optimal power extraction and power control of a doubly fed induction generator (DFIG) using backstepping control,” Engineering Research Express, vol. 6, no. 1, 2024, https://doi.org/10.1088/2631-8695/ad153d.
[23] A. Kasbi and A. Rahali, “Performance improvement of modern variable-velocity wind turbines technology based on the doubly-fed induction generator (DFIG),” Materialstoday Proceedings, vol. 45, pp. 5426–5432, 2021, https://doi.org/10.1016/j.matpr.2021.02.114.
[24] B. Peng, F. Zhang, J. Liang, L. Ding, Z. Liang, and Q. Wu, “Coordinated control strategy for the short-term frequency response of a DFIG-ES system based on wind speed zone classification and fuzzy logic control,” International Journal of Electrical Power & Energy Systems, vol. 107, pp. 363–378, 2019, https://doi.org/10.1016/j.ijepes.2018.11.010.
[25] R. Antão, Type-2 fuzzy logic: uncertain systems’ modeling and control, Springer, 2017, https://www.google.co.id/books/edition/Type_2_Fuzzy_Logic/QPQtDwAAQBAJ?hl=en&gbpv=0.
[26] Z. Civelek, “Optimization of fuzzy logic (Takagi-Sugeno) blade pitch angle controller in wind turbines by genetic algorithm,” Engineering Science and Technology, an International Journal, vol. 23, no. 1, pp. 1–9, 2020, https://doi.org/10.1016/j.jestch.2019.04.010.
[27] A. V. Hemeyine, A. Abbou, N. Tidjani, M. Mokhlis, and A. Bakouri, “Robust takagi sugeno fuzzy models control for a variable speed wind turbine based a DFI-generator,” International Journal of Intelligent Engineering and Systems, vol. 13, no. 3, pp. 90–100, 2020, https://doi.org/10.22266/ijies2020.0630.09.
[28] S. Qin, S. S. Ngu, and T. Zeng, “Optimal constant power control of wind turbine generators based on Takagi-Sugeno fuzzy model,” Alexandria Engineering Journal, vol. 61, no. 8, pp. 5977–5982, 2022, https://doi.org/10.1016/j.aej.2021.11.024.
[29] M. S. Chabani et al., “Takagi–Sugeno Fuzzy Logic Controller for DFIG Operating in the Stand-Alone Mode: Simulations and Experimental Investigation,” Arabian Journal for Science and Engineering, vol. 48, no. 11, pp. 14605–14620, 2023, https://doi.org/10.1007/s13369-023-07704-0.
[30] A. A. Chhipa et al., “Adaptive neuro‐fuzzy inference system‐based maximum power tracking controller for variable speed wecs,” Energies, vol. 14, no. 19, p. 6275, 2021, https://doi.org/10.3390/en14196275.
[31] P. Kou, D. Liang, J. Li, L. Gao and Q. Ze, "Finite-Control-Set Model Predictive Control for DFIG Wind Turbines," IEEE Transactions on Automation Science and Engineering, vol. 15, no. 3, pp. 1004-1013, 2018, https://doi.org/10.1109/TASE.2017.2682559.
[32] G. F. Gontijo, T. C. Tricarico, B. W. França, L. F. da Silva, E. L. van Emmerik and M. Aredes, "Robust Model Predictive Rotor Current Control of a DFIG Connected to a Distorted and Unbalanced Grid Driven by a Direct Matrix Converter," IEEE Transactions on Sustainable Energy, vol. 10, no. 3, pp. 1380-1392, 2019, https://doi.org/10.1109/TSTE.2018.2868406.
[33] M. Abdelrahem and R. Kennel, “Efficient Direct Model Predictive Control for Doubly-Fed Induction Generators,” Electric Power Components and Systems, vol. 45, no. 5, pp. 574–587, 2017, https://doi.org/10.1080/15325008.2017.1289572.
[34] A. J. Sguarezi Filho, A. L. De Oliveira, L. L. Rodrigues, E. C. M. Costa, and R. V. Jacomini, “A robust finite control set applied to the DFIG Power Control,” Electric Power Components and Systems, vol. 6, no. 4, pp. 1692–1698, 2018, https://doi.org/10.1080/15325008.2017.1289572.
[35] A. J. Sguarezi Filho, A. L. de Oliveira, L. L. Rodrigues, E. C. M. Costa and R. V. Jacomini, "A Robust Finite Control Set Applied to the DFIG Power Control," IEEE Journal of Emerging and Selected Topics in Power Electronics, vol. 6, no. 4, pp. 1692-1698, 2018, https://doi.org/10.1109/JESTPE.2018.2833474.
[36] H. El Alami et al., “Robust Finite Control-Set Model Predictive Control for Power Quality Enhancement of a Wind System Based on the DFIG Generator,” Energies, vol. 16, no. 3, p. 1422, 2023, https://doi.org/10.3390/en16031422.
[37] K. A. Naik, C. P. Gupta, and E. Fernandez, “Design and implementation of interval type-2 fuzzy logic-PI based adaptive controller for DFIG based wind energy system,” International Journal of Electrical Power & Energy Systems, vol. 115, p. 105468, 2020, https://doi.org/10.1016/j.ijepes.2019.105468.
[38] J. Pande, P. Nasikkar, K. Kotecha, and V. Varadarajan, “A review of maximum power point tracking algorithms for wind energy conversion systems,” Journal of Marine Science and Engineering, vol. 9, no. 11, p. 1187, 2021, https://doi.org/10.3390/jmse9111187.
[39] Y. Wang, L. Zou, L. Ma, Z. Zhao, and J. Guo, “A survey on control for Takagi-Sugeno fuzzy systems subject to engineering-oriented complexities,” Systems Science & Control Engineering, vol. 9, no. 1, pp. 334–349, 2021, https://doi.org/10.1080/21642583.2021.1907259.
[40] A. Ammar, B. Talbi, T. Ameid, Y. Azzoug, and A. Kerrache, “Predictive direct torque control with reduced ripples for induction motor drive based on T-S fuzzy speed controller,” Asian Journal of Control, vol. 21, no. 4, pp. 2155–2166, 2019, https://doi.org/10.1002/asjc.2148.
[41] V. Yaramasu and B. Wu, Model Predictive Control of Wind Energy Conversion Systems, John Wiley & Sons, 2016, https://doi.org/10.1002/9781119082989.
[42] A. Aggoune, F. Berrezzek, and K. Khelil, “Finite-Control-Set Model Predictive Control (FCS-MPC) and Fuzzy Self-Adaptive PI Controller (FSA-PIC) for Wind Turbine System Based on DFIG,” Proceedings of the 2nd International Conference of Nanotechnology for Environmental Protection and Clean Energy Production, vol. 45, pp. 327–338, 2024, https://doi.org/10.1007/978-981-97-1916-7_34.
Refbacks
- There are currently no refbacks.
Copyright (c) 2025 Amira Aggoune
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
| About the Journal | Journal Policies | Author | Information |
International Journal of Robotics and Control Systems
e-ISSN: 2775-2658
Website: https://pubs2.ascee.org/index.php/IJRCS
Email: ijrcs@ascee.org
Organized by: Association for Scientific Computing Electronics and Engineering (ASCEE), Peneliti Teknologi Teknik Indonesia, Department of Electrical Engineering, Universitas Ahmad Dahlan and Kuliah Teknik Elektro
Published by: Association for Scientific Computing Electronics and Engineering (ASCEE)
Office: Jalan Janti, Karangjambe 130B, Banguntapan, Bantul, Daerah Istimewa Yogyakarta, Indonesia