A Comparative Study of PID, FOPID, ISF, SMC, and FLC Controllers for DC Motor Speed Control with Particle Swarm Optimization
(1) Muhammad Haryo Setiawan Mail (Universitas Ahmad Dahlan, Indonesia)
(2) * Alfian Ma'arif Mail (Universitas Ahmad Dahlan, Indonesia)
(3) Much. Fuad Saifuddin Mail (Association for Scientific Computing Electronics and Engineering (ASCEE), Indonesia)
(4) Wael A. Salah Mail (Palestine Technical University, Palestinian Territory, Occupied)
*corresponding author

Abstract


Direct Current (DC) motors are extensively used in various applications due to their versatile and precise control capabilities. However, they face operational challenges such as speed instability and sensitivity to load variations and external disturbances. This study compares the performance of several advanced control methods—Proportional Integral Derivative (PID), Fractional Order PID (FOPID), Integral State Feedback (ISF), Sliding Mode Control (SMC), and Fuzzy Logic Controller (FLC) for DC motor control. Particle Swarm Optimization (PSO) is employed to optimize the tuning parameters of PID, FOPID, ISF, and SMC controllers, while FLC is implemented without optimization. The simulation results indicate that the PSO-FOPID controller exhibits the best overall performance, characterized by the fastest rise and settling times and the lowest ITSE, despite a minor overshoot. The PSO-PID controller also performs well, with fast response times, although it is less efficient in terms of settling time and ITSE compared to PSO-FOPID. The OBL/HGSO-PID controller, while stable and overshoot-free, has a slower response. The PSO-ISF controller shows the highest stability with the lowest SSE values, making it suitable for applications requiring high stability. The PSO-SMC controller demonstrates good stability but is slightly slower than PSO-ISF. The FLC controller, however, performs the worst, with significant overshoot and long recovery times, making it unsuitable for fast and precise control applications.  The robustness analysis under varying motor parameters further confirms the superiority of the PSO-FOPID controller, which outperforms OBL/HGSO and OBL-MRFO-SA optimizations across both PID and FOPID controllers, making it the most effective solution for applications requiring high precision and rapid response.

Keywords


DC Motor; PID Control; FOPID Control; Integral State Feedback; Sliding Mode Control; Fuzzy Logic Control; Particle Swarm Optimization

   

DOI

https://doi.org/10.31763/ijrcs.v5i1.1764 		      

Article metrics

10.31763/ijrcs.v5i1.1764 Abstract views : 130 | PDF views : 57

   

Cite

How to cite item
   

Full Text

Download

References


[1] A. H. Sabry, A. H. Shallal, H. S. Hameed, and P. J. Ker, “Compatibility of household appliances with DC microgrid for PV systems,” Heliyon, vol. 6, no. 12, p. e05699, 2020, https://doi.org/10.1016/j.heliyon.2020.e05699.

[2] M. Nandakumar, S. Ramalingam, S. Nallusamy, and S. Srinivasarangan Rangarajan, “Hall-Sensor-Based Position Detection for Quick Reversal of Speed Control in a BLDC Motor Drive System for Industrial Applications,” Electronics, vol. 9, no. 7, p. 1149, 2020, https://doi.org/10.3390/electronics9071149.

[3] N. Shah, W.Y. Park, and C. Ding, “Trends in best-in-class energy-efficient technologies for room air conditioners,” Energy Reports, vol. 7, pp. 3162-3170, 2021, https://doi.org/10.1016/j.egyr.2021.05.016.

[4] D. Mohanraj et al., "A Review of BLDC Motor: State of Art, Advanced Control Techniques, and Applications," IEEE Access, vol. 10, pp. 54833-54869, 2022, https://doi.org/10.1109/ACCESS.2022.3175011.

[5] K. Mohammed, J. A. F. Yahaya, and R. B. Khan, “Applied measurement of the motor speed controller for washing machine with random loads, part II,” International Journal of Power Electronics and Drive Systems (IJPEDS), vol. 11, no. 1, pp. 442-450, 2020, http://doi.org/10.11591/ijpeds.v11.i1.pp442-450.

[6] Y. Choo et al., "Investigation of Systematic Efficiency in a High-Speed Single-Phase Brushless DC Motor Using Multi-Physics Analysis for a Vacuum Cleaner," IEEE Transactions on Magnetics, vol. 55, no. 7, pp. 1-6, 2019, https://doi.org/10.1109/TMAG.2019.2903445.

[7] V. S. Panwar, A. Pandey, and M. E. Hasan, “Design and fabrication of a novel concept-based autonomous controlled solar powered four-wheeled Floor Cleaning Robot for wet and dry surfaces,” International Journal of Information Technology, vol. 14, no. 4, pp. 1995-2004, 2022, https://doi.org/10.1007/s41870-022-00893-1.

[8] O. V. Shepovalova, A. T. Belenov, and S. V. Chirkov, “Review of photovoltaic water pumping system research,” Energy Reports, vol. 6, pp. 306-324, 2020, https://doi.org/10.1016/j.egyr.2020.08.053.

[9] H. Yang, Z. Wang, T. Zhang, and F. Du, “A review on vibration analysis and control of machine tool feed drive systems,” The International Journal of Advanced Manufacturing Technology, vol. 107, pp. 503-525, 2020, https://doi.org/10.1007/s00170-020-05041-2.

[10] Y. M. Hendrawan, A. Farrage, and N. Uchiyama, “Iterative NC program modification and energy saving for a CNC machine tool feed drive system with linear motors,” The International Journal of Advanced Manufacturing Technology, vol. 102, pp. 3543-3562, 2019, https://doi.org/10.1007/s00170-019-03390-1.

[11] A. Ramaswamy and M. Muniraj, “Investigation of an Intellectual Tracking System Using the Intelligent Controller for Infusion Pump in Medical Applications,” Brazilian Archives of Biology and Technology, vol. 67, 2024, https://doi.org/10.1007/s00170-019-03390-1.

[12] L. A. O’Connor, B. Houseman, T. Cook, and C. C. Quinn, “Intercostal cryonerve block versus elastomeric infusion pump for postoperative analgesia following surgical stabilization of traumatic rib fractures,” Injury, vol. 54, no. 11, p. 111053, 2023, https://doi.org/10.1007/s00170-019-03390-1.

[13] V. Sankardoss and P. Geethanjali, “Design and Low-Cost Implementation of an Electric Wheelchair Control,” IETE Journal of Research, vol. 67, no. 5, pp. 657–666, 2021, https://doi.org/10.1080/03772063.2019.1565951.

[14] J. Arcos-Legarda and A. Tovar, “Mechatronic Design and Active Disturbance Rejection Control of a Bag Valve-Based Mechanical Ventilator,” Journal of Medical Devices, vol. 15, no. 3, p. 031006, 2021, https://doi.org/10.1115/1.4051064.

[15] R. Hernandez-Alvarado, O. Rodriguez-Abreo, J. M. Garcia-Guendulain, and T. Hernandez-Diaz, “Self-Tuning Control Using an Online-Trained Neural Network to Position a Linear Actuator,” Micromachines, vol. 13, no. 5, p. 696, 2022, https://doi.org/10.3390/mi13050696.

[16] R. Saputra, and N. Surantha, “Smart and real-time door lock system for an elderly user based on face recognition,” Bulletin of Electrical Engineering and Informatics, vol. 10, no. 3, pp. 1345-1355, 2021, https://doi.org/10.11591/eei.v10i3.2955.

[17] J. Guntur, S. S. Raju, T. Niranjan, S. K. Kilaru, R. Dronavalli, and N. S. S. Kumar, “IoT-Enhanced Smart Door Locking System with Security,” SN Computer Science, vol. 4, no. 2, p. 209, 2023, https://doi.org/10.1007/s42979-022-01641-9.

[18] F. Z. Baouche et al., “Design and Simulation of a Solar Tracking System for PV,” Applied Sciences, vol. 12, no. 19, p. 9682, 2022, https://doi.org/10.3390/app12199682.

[19] A. Karabiber and Y. Güneş, “Single-motor and dual-axis solar tracking system for micro photovoltaic power plants,” Journal of Solar Energy Engineering, vol. 145, no. 5, p.051004, 2023, https://doi.org/10.1115/1.4056739.

[20] S. S. Nielsen, R. K. Holm and P. O. Rasmussen, "Conveyor System With a Highly Integrated Permanent Magnet Gear and Motor," IEEE Transactions on Industry Applications, vol. 56, no. 3, pp. 2550-2559, 2020, https://doi.org/10.1109/TIA.2020.2977877.

[21] M. Q. Zaman and H. -M. Wu, "Intelligent Motion Control Design for an Omnidirectional Conveyor System," IEEE Access, vol. 11, pp. 47351-47361, 2023, https://doi.org/10.1109/ACCESS.2023.3275962.

[22] S. Sukamta, A. Nugroho, Subiyanto, R. Rezianto, M. F. Soambaton, and A. Ardiyanto, “Image-Based Position Control for Three-Wheel Omni-Directional Robot,” Jurnal Ilmiah Teknik Elektro Komputer dan Informatika (JITEKI), vol. 10, no. 3, pp. 566-579, 2024, https://doi.org/10.26555/jiteki.v10i3.29601.

[23] S. H. Yen, P. C. Tang, Y. C. Lin, and C. Y. Lin, “A sensorless and low-gain brushless DC motor controller using a simplified dynamic force compensator for robot arm application,” Sensors, vol. 19, no. 14, p. 3171, 2019, https://doi.org/10.3390/s19143171.

[24] Fahmizal, M. S. Pratikno, H. N. Isnianto, A. Mayub, H. Maghfiroh, and P. Anugrah, “Control and Navigation of Differential Drive Mobile Robot with PID and Hector SLAM: Simulation and Implementation,” Jurnal Ilmiah Teknik Elektro Komputer dan Informatika (JITEKI), vol. 10, no. 3, pp. 594–607, 2024, https://doi.org/10.26555/jiteki.v10i3.29428.

[25] N. X. Chiem, “Cascade Control for Trajectory-Tracking Mobile Robots Based on Synergetic Control Theory and Lyapunov Functions,” Control Systems and Optimization Letters, vol. 3, no. 1, pp. 14-19, 2025, https://doi.org/10.59247/csol.v3i1.169.

[26] H. Khan, S. Khatoon, and P. Gaur, “Comparison of various controller design for the speed control of DC motors used in two wheeled mobile robots,” International Journal of Information Technology, vol. 13, no. 2, pp. 713-720, 2021, https://doi.org/10.1007/s41870-020-00577-8.

[27] C. Iwendi, M. A. Alqarni, J. H. Anajemba, A. S. Alfakeeh, Z. Zhang and A. K. Bashir, "Robust Navigational Control of a Two-Wheeled Self-Balancing Robot in a Sensed Environment," IEEE Access, vol. 7, pp. 82337-82348, 2019, https://doi.org/10.1109/ACCESS.2019.2923916.

[28] G. Curiel-Olivares, J. Linares-Flores, J. F. Guerrero-Castellanos, and A. Hernández-Méndez, “Self-balancing based on Active Disturbance Rejection Controller for the Two-In-Wheeled Electric Vehicle, Experimental results,” Mechatronics, vol. 76, p. 102552, 2021, https://doi.org/10.1016/j.mechatronics.2021.102552.

[29] Y. Yaşa, “An Efficient Brushless DC Motor Design for Unmanned Aerial Vehicles,” European Journal of Science and Technology, no. 35, pp. 288-294, 2022, https://doi.org/10.31590/ejosat.1083838.

[30] A. Bosso, C. Conficoni, D. Raggini and A. Tilli, "A Computational-Effective Field-Oriented Control Strategy for Accurate and Efficient Electric Propulsion of Unmanned Aerial Vehicles," IEEE/ASME Transactions on Mechatronics, vol. 26, no. 3, pp. 1501-1511, 2021, https://doi.org/10.1109/TMECH.2020.3022379.

[31] Y. Jouili, R. Garraoui, M. Ben Hamed, and L. Sbita, “Self-Adaptive PI-FLC for BLDC Motor Speed Supplied by PEM Fuel Cell Stack Optimized by MPPT,” Arabian Journal for Science and Engineering, vol. 49, no. 5, pp. 6487–6503, 2024, https://doi.org/10.1007/s13369-023-08265-y.

[32] B. Darmono, H. Pranoto, and Z. Arifin, “Torque Analysis of 2 KW BLDC (Brushless Direct Current) Motor with Speed Variations in Electric Cars E-Falco,” International Journal of Advanced Technology in Mechanical, Mechatronics and Materials, vol. 2, no. 2, pp. 76–86, 2021, https://doi.org/10.37869/ijatec.v2i2.47.

[33] F. A. Pamuji et al., “Application of Artificial Neural Network for Speed Control of BLDC Motor 90KW in Electrical Bus,” Przegląd Elektrotechniczny, vol. 1, no. 2, pp. 205–212, 2022, https://doi.org/10.15199/48.2022.02.47.

[34] T. K. Nizami, A. Chakravarty, C. Mahanta, A. Iqbal, and A. Hosseinpour, “Enhanced dynamic performance in DC–DC converter‐PMDC motor combination through an intelligent non‐linear adaptive control scheme,” IET Power Electronics, vol. 15, no. 15, pp. 1607–1616, 2022, https://doi.org/10.15199/48.2022.02.47.

[35] S. Ekinci, D. Izci and M. Yilmaz, "Efficient Speed Control for DC Motors Using Novel Gazelle Simplex Optimizer," IEEE Access, vol. 11, pp. 105830-105842, 2023, https://doi.org/10.1109/ACCESS.2023.3319596.

[36] F. Alanazi, “Electric Vehicles: Benefits, Challenges, and Potential Solutions for Widespread Adaptation,” Applied Sciences, vol. 13, no. 10, p. 6016, 2023, https://doi.org/10.3390/app13106016.

[37] X. Zhu, H. Shi, C. Zhang, Y. Du, L. Xu and L. Zhang, "Speed Ripple Suppression of Permanent Magnet Hub Motor Based on ADRC With Observer Error Constraints," IEEE Transactions on Industrial Electronics, vol. 72, no. 2, pp. 1205-1216, 2025, https://doi.org/10.1109/TIE.2024.3409902.

[38] Q. Xu, Y. Wang, X. Chen, and W. Cao, “Research on Dynamic Reactive Power Cost Optimization in Power Systems with DFIG Wind Farms,” Processes, vol. 12, no. 5, p. 872, 2024, https://doi.org/10.3390/pr12050872.

[39] H. Djouadi, K. Ouari, Y. Belkhier, H. Lehouche, M. Bajaj, and V. Blazek, “Improved robust model predictive control for PMSM using backstepping control and incorporating integral action with experimental validation,” Results in Engineering, vol. 23, p. 102416, 2024, https://doi.org/10.1016/j.rineng.2024.102416.

[40] J. Rodriguez et al., "Latest Advances of Model Predictive Control in Electrical Drives—Part I: Basic Concepts and Advanced Strategies," IEEE Transactions on Power Electronics, vol. 37, no. 4, pp. 3927-3942, 2022, https://doi.org/10.1109/TPEL.2021.3121532.

[41] K. Xu, W. Liang, W. Zhao, C. Wang, S. Zou and X. Zhou, "Vehicle Stability and Synchronization Control of Dual-Motor Steer-by-Wire System Considering Multiple Uncertainties," IEEE Transactions on Transportation Electrification, vol. 10, no. 2, pp. 3092-3104, 2024, https://doi.org/10.1109/TTE.2023.3304048.

[42] A. Lotfy, M. Kaveh, M. R. Mosavi, and A. R. Rahmati, “An enhanced fuzzy controller based on improved genetic algorithm for speed control of DC motors,” Analog Integr Circuits Signal Process, vol. 105, no. 2, pp. 141–155, 2020, https://doi.org/10.1007/s10470-020-01599-9.

[43] A. Irawan, M. H. Sulaiman, M. S. Ramli, and M. I. P. Azahar, “Pneumatic servo position control optimization using adaptive-domain prescribed performance control with evolutionary mating algorithm,” Results in Control and Optimization, vol. 15, p. 100434, 2024, https://doi.org/10.1016/j.rico.2024.100434.

[44] S. Ekinci, B. Hekimoğlu, and D. Izci, “Opposition based Henry gas solubility optimization as a novel algorithm for PID control of DC motor,” Engineering Science and Technology, an International Journal, vol. 24, no. 2, pp. 331–342, 2021, https://doi.org/10.1016/j.jestch.2020.08.011.

[45] S. Ekinci, D. Izci, and B. Hekimoğlu, “Optimal FOPID Speed Control of DC Motor via Opposition-Based Hybrid Manta Ray Foraging Optimization and Simulated Annealing Algorithm,” Arabian Journal for Science and Engineering, vol. 46, no. 2, pp. 1395–1409, 2021, https://doi.org/10.1007/s13369-020-05050-z.

[46] B. Zhang and X. Tang, “High-performance state feedback controller for permanent magnet synchronous motor,” ISA Transactions, vol. 118, pp. 144–158, 2021, https://doi.org/10.1016/j.isatra.2021.02.009.

[47] M. Zhang, X. Jing, W. Huang, and P. Li, “Saturated PD-SMC method for suspension systems by exploiting beneficial nonlinearities for improved vibration reduction and energy-saving performance,” Mechanical Systems and Signal Processing, vol. 179, p. 109376, 2022, https://doi.org/10.1016/j.ymssp.2022.109376.

[48] X. He et al., “Improved beluga whale optimization-based variable universe fuzzy controller for brushless direct current motors of electric tractors,” Computers and Electrical Engineering, vol. 120, p. 109866, 2024, https://doi.org/10.1016/j.compeleceng.2024.109866.

[49] B. F. Barreiros, J. O. Trierweiler, and M. Farenzena, “Reliable and straightforward PID tuning rules for highly underdamped systems,” Brazilian Journal of Chemical Engineering, vol. 38, no. 4, pp. 731–745, 2021, https://doi.org/10.1016/j.compeleceng.2024.109866.

[50] D. Gupta, V. Goyal, and J. Kumar, “Comparative performance analysis of fractional-order nonlinear PID controller for complex surge tank system: tuning through machine learning control approach,” Multimedia Tools and Applications, vol. 83, no. 33, pp. 78923–78956, 2024, https://doi.org/10.1007/s11042-024-18427-1.

[51] Y. Liu et al., "Dynamic State Estimation for Power System Control and Protection," IEEE Transactions on Power Systems, vol. 36, no. 6, pp. 5909-5921, 2021, https://doi.org/10.1109/TPWRS.2021.3079395.

[52] W. Qi, G. Zong, Y. Hou and M. Chadli, "SMC for Discrete-Time Nonlinear Semi-Markovian Switching Systems With Partly Unknown Semi-Markov Kernel," IEEE Transactions on Automatic Control, vol. 68, no. 3, pp. 1855-1861, 2023, https://doi.org/10.1109/TAC.2022.3169584.

[53] K. Sivakumar and S. Appasamy, “Fuzzy Mathematical Approach for Solving Multi-Objective Fuzzy Linear Fractional Programming Problem with Trapezoidal Fuzzy Numbers,” Mathematical Modelling of Engineering Problems, vol. 11, no. 1, pp. 255–262, 2024, https://doi.org/10.18280/mmep.110128.

[54] R. Szczepanski, M. Kaminski, and T. Tarczewski, “Auto-Tuning Process of State Feedback Speed Controller Applied for Two-Mass System,” Energies, vol. 13, no. 12, p. 3067, 2020, https://doi.org/10.3390/en13123067.

[55] B. N. Kommula and V. R. Kota, “Design of MFA-PSO based fractional order PID controller for effective torque controlled BLDC motor,” Sustainable Energy Technologies and Assessments, vol. 49, p. 101644, 2022, https://doi.org/10.1016/j.seta.2021.101644.

[56] M. G. M. Abdolrasol, M. A. Hannan, S. M. S. Hussain, and T. S. Ustun, “Optimal PI controller based PSO optimization for PV inverter using SPWM techniques,” Energy Reports, vol. 8, pp. 1003–1011, 2022, https://doi.org/10.1016/j.egyr.2021.11.180.

[57] H. Abdelfattah, A. O. Aseeri, and M. Abd Elaziz, “Optimized FOPID controller for nuclear research reactor using enhanced planet optimization algorithm,” Alexandria Engineering Journal, vol. 97, pp. 267–282, 2024, https://doi.org/10.1016/j.aej.2024.04.021.

[58] S. K. Majhi, M. Sahoo, and R. Pradhan, “Oppositional Crow Search Algorithm with mutation operator for global optimization and application in designing FOPID controller,” Evolving Systems, vol. 12, no. 2, pp. 463–488, 2021, https://doi.org/10.1007/s12530-019-09305-5.

[59] S. Arun and T. Manigandan, “Design of ACO based PID controller for zeta converter using reduced order methodology,” Microprocessors and Microsystems, vol. 81, p. 103629, 2021, https://doi.org/10.1016/j.micpro.2020.103629.

[60] B. Arun, B. V. Manikandan, and K. Premkumar, “Multiarea Power System Performance Measurement using Optimized PID Controller,” Microprocessors and Microsystems, p. 104238, 2021, https://doi.org/10.1016/j.micpro.2021.104238.

[61] M. N. Ali, M. Soliman, K. Mahmoud, J. M. Guerrero, M. Lehtonen and M. M. F. Darwish, "Resilient Design of Robust Multi-Objectives PID Controllers for Automatic Voltage Regulators: D-Decomposition Approach," IEEE Access, vol. 9, pp. 106589-106605, 2021, https://doi.org/10.1109/ACCESS.2021.3100415.

[62] M. Khamies, G. Magdy, M. Ebeed, and S. Kamel, “A robust PID controller based on linear quadratic gaussian approach for improving frequency stability of power systems considering renewables,” ISA Transactions, vol. 117, pp. 118–138, 2021, https://doi.org/10.1016/j.isatra.2021.01.052.

[63] F. Naz et al., “PID Tuning with reference tracking and plant uncertainty along with disturbance rejection,” Systems Science & Control Engineering, vol. 9, no. 1, pp. 160–166, 2021, https://doi.org/10.1080/21642583.2021.1888817.

[64] L. Hazeleger, R. Beerens and N. van de Wouw, "Proportional–Integral–Derivative-Based Learning Control for High-Accuracy Repetitive Positioning of Frictional Motion Systems," IEEE Transactions on Control Systems Technology, vol. 29, no. 4, pp. 1652-1663, 2021, https://doi.org/10.1109/TCST.2020.3017803.

[65] P. Razmi, T. Rahimi, K. Sabahi, M. Gheisarnejad, and M. Khooban, “Adaptive fuzzy gain scheduling PID controller for frequency regulation in modern power system,” IET Renewable Power Generation, vol. 2022, no. 1, pp. 1-16, 2022, https://doi.org/10.1049/rpg2.12569.

[66] L. Wang, J. Liu, C. Yang, and D. Wu, “A novel interval dynamic reliability computation approach for the risk evaluation of vibration active control systems based on PID controllers,” Applied Mathematical Modelling, vol. 92, pp. 422–446, 2021, https://doi.org/10.1016/j.apm.2020.11.007.

[67] M. Sharma, S. Sharma, and J. Vajpai, “A novel approach to design and analyze fractional order PID controller for speed control of brushless DC motor,” Renewable Energy and Sustainable Development, vol. 10, no. 2, p. 279, 2024, http://dx.doi.org/10.21622/resd.2024.10.2.903.

[68] M. Huba, S. Chamraz, P. Bistak, and D. Vrancic, “Making the PI and PID Controller Tuning Inspired by Ziegler and Nichols Precise and Reliable,” Sensors, vol. 21, no. 18, p. 6157, 2021, https://doi.org/10.3390/s21186157.

[69] D. A. Souza, J. G. Batista, L. L. N. dos Reis, and A. B. S. Júnior, “PID controller with novel PSO applied to a joint of a robotic manipulator,” Journal of the Brazilian Society of Mechanical Sciences and Engineering, vol. 43, no. 8, p. 377, 2021, https://doi.org/10.1007/s40430-021-03092-4.

[70] A. Ali, K. Bingi, R. Ibrahim, P. A. M. Devan, and K. B. Devika, “A review on FPGA implementation of fractional-order systems and PID controllers,” AEU-International Journal of Electronics and Communications, vol. 177, p. 155218, 2024, https://doi.org/10.1016/j.aeue.2024.155218.

[71] E. A. Mohamed, E. M. Ahmed, A. Elmelegi, M. Aly, O. Elbaksawi and A. -A. A. Mohamed, "An Optimized Hybrid Fractional Order Controller for Frequency Regulation in Multi-Area Power Systems," IEEE Access, vol. 8, pp. 213899-213915, 2020, https://doi.org/10.1109/ACCESS.2020.3040620.

[72] B. Khokhar, S. Dahiya, and K. P. S. Parmar, “A novel fractional order proportional integral derivative plus second-order derivative controller for load frequency control,” International Journal of Sustainable Energy, vol. 40, no. 3, pp. 235–252, 2021, https://doi.org/10.1080/14786451.2020.1803861.

[73] W. Zheng, Y. Chen, X. Wang, M. Lin, and J. Guo, “Robust fractional order PID controller synthesis for the first order plus integral system,” Measurement and Control, vol. 56, no. 1–2, pp. 202–214, 2023, https://doi.org/10.1177/00202940221095564.

[74] O. W. Abdulwahhab, “Design of a Complex fractional Order PID controller for a First Order Plus Time Delay system,” ISA Transactions, vol. 99, pp. 154–158, 2020, https://doi.org/10.1016/j.isatra.2019.10.010.

[75] R. Mok and M. A. Ahmad, “Fast and optimal tuning of fractional order PID controller for AVR system based on memorizable-smoothed functional algorithm,” Engineering Science and Technology, an International Journal, vol. 35, p. 101264, 2022, https://doi.org/10.1016/j.jestch.2022.101264.

[76] M. A. Ebrahim, M. Becherif, and A. Y. Abdelaziz, “PID-/FOPID-based frequency control of zero-carbon multisources-based interconnected power systems underderegulated scenarios,” International Transactions on Electrical Energy Systems, vol. 31, no. 2, 2021, https://doi.org/10.1002/2050-7038.12712.

[77] A. Rajendran, M. Karthikeyan, and G. Saravanakumar, “Implementation of FOPID controller with modified harmony search optimization for precise modelling and auto-tuning of nonlinear systems,” Automatika, vol. 65, no. 3, pp. 881-893, 2024, https://doi.org/10.1080/00051144.2024.2307227.

[78] I. Iswanto and A. Ma’arif, "Robust Integral State Feedback Using Coefficient Diagram in Magnetic Levitation System," IEEE Access, vol. 8, pp. 57003-57011, 2020, https://doi.org/10.1109/ACCESS.2020.2981840.

[79] H. Du, J. Shi, J. Chen, Z. Zhang, and X. Feng, “High-gain observer-based integral sliding mode tracking control for heavy vehicle electro-hydraulic servo steering systems,” Mechatronics, vol. 74, p. 102484, 2021, https://doi.org/10.1016/j.mechatronics.2021.102484.

[80] A. Ma’arif, I. Suwarno, E. Nur’aini, and N. M. Raharja, “Altitude Control of UAV Quadrotor Using PID and Integral State Feedback,” BIO Web Conferences, vol. 65, p. 07011, 2023, https://doi.org/10.1051/bioconf/20236507011.

[81] B. Lu, Y. Fang and N. Sun, "Continuous Sliding Mode Control Strategy for a Class of Nonlinear Underactuated Systems," IEEE Transactions on Automatic Control, vol. 63, no. 10, pp. 3471-3478, 2018, https://doi.org/10.1109/TAC.2018.2794885.

[82] X. Yu, Y. Feng and Z. Man, "Terminal Sliding Mode Control – An Overview," IEEE Open Journal of the Industrial Electronics Society, vol. 2, pp. 36-52, 2021, https://doi.org/10.1109/OJIES.2020.3040412.

[83] S. M. Amrr and A. Alturki, "Robust Control Design for an Active Magnetic Bearing System Using Advanced Adaptive SMC Technique," IEEE Access, vol. 9, pp. 155662-155672, 2021, https://doi.org/10.1109/ACCESS.2021.3129140.

[84] H. H. Tang and N. S. Ahmad, “Fuzzy logic approach for controlling uncertain and nonlinear systems: a comprehensive review of applications and advances,” Systems Science & Control Engineering, vol. 12, no. 1, 2024, https://doi.org/10.1080/21642583.2024.2394429.

[85] F. Sabahi, “Optimal bounded policy for nonlinear tracking control of unknown constrained-input systems,” Transactions of the Institute of Measurement and Control, vol. 47, no. 3, pp. 585-598, 2024, https://doi.org/10.1177/01423312241254590.

[86] J. Zhao, T. Zhao, K. Nie, and Y. Mao, “A Fuzzy Dual Closed-Loop Control Scheme for Precision Stabilized Platform,” International Journal of Fuzzy Systems, 2024, https://doi.org/10.1007/s40815-024-01882-1.

[87] M. Praharaj, D. Sain, and B. M. Mohan, “Development, experimental validation, and comparison of interval type-2 Mamdani fuzzy PID controllers with different footprints of uncertainty,” Information Sciences, vol. 601, pp. 374–402, 2022, https://doi.org/10.1016/j.ins.2022.03.095.

[88] R. Datta, R. Saravanakumar, R. Dey, B. Bhattacharya, and C. K. Ahn, “Improved stabilization criteria for Takagi–Sugeno fuzzy systems with variable delays,” Information Sciences, vol. 579, pp. 591–606, 2021, https://doi.org/10.1016/j.ins.2021.07.089.

[89] H. Yonezawa, A. Yonezawa, T. Hatano, S. Hiramatsu, C. Nishidome, and I. Kajiwara, “Fuzzy-reasoning-based robust vibration controller for drivetrain mechanism with various control input updating timings,” Mechanism and Machine Theory, vol. 175, p. 104957, 2022, https://doi.org/10.1016/j.mechmachtheory.2022.104957.

[90] Q. A. Tarbosh et al., "Review and Investigation of Simplified Rules Fuzzy Logic Speed Controller of High Performance Induction Motor Drives," IEEE Access, vol. 8, pp. 49377-49394, 2020, https://doi.org/10.1109/ACCESS.2020.2977115.

[91] D. Kalibatiene and J. Miliauskaitė, “A dynamic fuzzification approach for interval type-2 membership function development: case study for QoS planning,” Soft computing, vol. 25, no. 16, pp. 11269–11287, 2021, https://doi.org/10.1007/s00500-021-05899-8.

[92] Ş. Yıldırım, M. S. Bingol, and S. Savas, “Tuning PID controller parameters of the DC motor with PSO algorithm,” International Review of Applied Sciences and Engineering, vol. 15, no. 3, pp. 281–286, 2024, https://doi.org/10.1556/1848.2023.00698.

[93] D. Zhang, G. Ma, Z. Deng, Q. Wang, G. Zhang, and W. Zhou, “A self-adaptive gradient-based particle swarm optimization algorithm with dynamic population topology,” Applied Soft Computing, vol. 130, p. 109660, 2022, https://doi.org/10.1016/j.asoc.2022.109660.

[94] S. M. H. Mousakazemi, “Comparison of the error-integral performance indexes in a GA-tuned PID controlling system of a PWR-type nuclear reactor point-kinetics model,” Progress in Nuclear Energy, vol. 132, p. 103604, 2021, https://doi.org/10.1016/j.pnucene.2020.103604.

[95] O. M. A. Al-hotmani, M. A. Al-Obaidi, J.-P. Li, Y. M. John, R. Patel, and I. M. Mujtaba, “A multi-objective optimisation framework for MED-TVC seawater desalination process based on particle swarm optimisation,” Desalination, vol. 525, p. 115504, 2022, https://doi.org/10.1016/j.desal.2021.115504.

[96] R. K. Agrawal, B. Kaur, and P. Agarwal, “Quantum inspired Particle Swarm Optimization with guided exploration for function optimization,” Applied Soft Computing, vol. 102, p. 107122, 2021, https://doi.org/10.1016/j.asoc.2021.107122.

[97] B. Zhao et al., "PriMPSO: A Privacy-Preserving Multiagent Particle Swarm Optimization Algorithm," IEEE Transactions on Cybernetics, vol. 53, no. 11, pp. 7136-7149, 2023, https://doi.org/10.1109/TCYB.2022.3224169.

[98] P. Chen and Y. Luo, "Analytical Fractional-Order PID Controller Design With Bode’s Ideal Cutoff Filter for PMSM Speed Servo System," IEEE Transactions on Industrial Electronics, vol. 70, no. 2, pp. 1783-1793, 2023, https://doi.org/10.1109/TIE.2022.3158009.

[99] Y. Wang, M. Pan, W. Zhou, and J. Huang, “Direct thrust control for variable cycle engine based on fractional order PID-nonlinear model predictive control under off-nominal operation conditions,” Aerospace Science and Technology, vol. 143, p. 108726, 2023, https://doi.org/10.1016/j.ast.2023.108726.

[100] J. Huang, Z. Lv, and J.-Q. Sun, “Optimal full-state feedback observer integrated backstepping control of chemical processes with unknown internal dynamics,” ISA Transactions, vol. 122, pp. 371–379, 2022, https://doi.org/10.1016/j.isatra.2021.05.009.


Refbacks

  • There are currently no refbacks.


Copyright (c) 2024 Muhammad Haryo Setiawan, Alfian Ma'arif

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

 

About the JournalJournal PoliciesAuthor Information

International Journal of Robotics and Control Systems
e-ISSN: 2775-2658
Website: https://pubs2.ascee.org/index.php/IJRCS
Email: ijrcs@ascee.org
Organized by: Association for Scientific Computing Electronics and Engineering (ASCEE), Peneliti Teknologi Teknik Indonesia, Department of Electrical Engineering, Universitas Ahmad Dahlan and Kuliah Teknik Elektro
Published by: Association for Scientific Computing Electronics and Engineering (ASCEE)
Office: Jalan Janti, Karangjambe 130B, Banguntapan, Bantul, Daerah Istimewa Yogyakarta, Indonesia