(2) Salam Waley Shneen (University of Technology, Iraq)
*corresponding author
AbstractAchieving high voltage and efficiency in brushless direct current (BLDC) motor applications is challenging, particularly in industrial settings where precise speed control is essential. This study addresses this issue by designing a cascaded boost converter with a Proportional–integral–derivative (PID) speed controller. The cascaded boost converter is first simulated in an open-loop circuit using MATLAB/SIMULINK, followed by integrating the BLDC motor and adding a PID controller to achieve precise speed control. The PID controller achieved a steady-state speed of 1500 rad/s with an input voltage of 15 volts, resulting in an output voltage of over 50 volts. The efficiency of the system was improved by 87.87% compared to traditional methods. While the PID controller effectively controls the motor speed, it may consume more power and require more complex tuning in certain operating conditions. The proposed system is suitable for high-voltage industrial applications, such as electric vehicle drives and renewable energy systems, where precise speed control and high efficiency are critical. The PID controller is user-friendly and easy to implement, making it suitable for various industrial applications. The system was tested under varying load conditions and input voltages to ensure robust performance and reliability. Future work will optimize the PID controller for real-time applications and integrate advanced control strategies to enhance system performance. A cascaded boost converter is a type of DC-DC converter that boosts the input voltage to a higher level, while a PID controller is a control loop feedback mechanism widely used for precise control of dynamic systems.
KeywordsCascaded Boost Converter (CBC); BLDC Motor; PID Controller; Speed Controller
|
DOIhttps://doi.org/10.31763/ijrcs.v5i1.1601 |
Article metrics10.31763/ijrcs.v5i1.1601 Abstract views : 108 | PDF views : 53 |
Cite |
Full TextDownload |
References
[1] Y. -S. Lee, W. -C. Lin and L. -C. Yu, "Design of a cascade high gain soft-switching boost converter," 2015 IEEE 11th International Conference on Power Electronics and Drive Systems, pp. 834-840, 2015, https://doi.org/10.1109/PEDS.2015.7203378.
[2] A. Al Zawaideh and I. M. Boiko, "Analysis of Stability and Performance of a Cascaded PI Sliding-Mode Control DC–DC Boost Converter via LPRS," IEEE Transactions on Power Electronics, vol. 37, no. 9, pp. 10455-10465, 2022, https://doi.org/10.1109/TPEL.2022.3169000.
[3] R. Kiguchi and Y. Nishida, "Cascaded Boost Converter to Achieve High Voltage Boost Rate - Conduction Loss Analysis," PCIM Europe 2019; International Exhibition and Conference for Power Electronics, Intelligent Motion, Renewable Energy and Energy Management, pp. 1-7, 2019, https://ieeexplore.ieee.org/document/8767495.
[4] S. W. Shneen, D. H. Shaker, and F. N. Abdullah, "Simulation model of PID for DC-DC converter by using MATLAB,” International Journal of Electrical and Computer Engineering, vol. 11, no. 5, pp. 3791-3797, 2021, http://doi.org/10.11591/ijece.v11i5.pp3791-3797.
[5] H. Gholizadeh, R. S. Shahrivar, M. R. Hashemi, E. Afjei and S. A. Gorji, "Design and implementation a single-switch step-up DC-DC converter based on cascaded boost and luo converters," Energies, vol. 14, no. 12, p. 3584, 2021, https://doi.org/10.3390/en14123584.
[6] S. W. Shneen, A. L. Shuraiji, K. R. Hameed, "Simulation model of proportional integral controller-PWM DC-DC power converter for DC motor using matlab," Indonesian Journal of Electrical Engineering and Computer Science, vol. 29, no. 2, pp. 725-734, 2023, http://doi.org/10.11591/ijeecs.v29.i2.pp725-734.
[7] D. Saputra, A. Ma'arif, H. Maghfiroh, P. Chotikunnan, S. N. Rahmadhia, "Design and application of PLC-based speed control for DC motor using PID with identification system and MATLAB tuner,” International Journal of Robotics and Control Systems, vol. 3, no. 2, pp. 233-244, 2023, https://doi.org/10.31763/ijrcs.v3i2.775.
[8] E. S. Rahayu, A. Ma’arif, and A. Cakan, "Particle swarm optimization (PSO) tuning of PID control on DC motor,” International Journal of Robotics and Control Systems, vol. 2, no. 2, pp. 453-447, 2022, https://doi.org/10.31763/ijrcs.v2i2.476.
[9] H. Zhu, "Research on PLC DC Motor Speed Control System Based on Quantum Fuzzy Control Algorithm," 2022 International Conference on Applied Artificial Intelligence and Computing (ICAAIC), pp. 1672-1675, 2022, https://doi.org/10.1109/ICAAIC53929.2022.9793235.
[10] J. R. B. A. Monteiro, C. M. R. Oliveira and M. L. Aguiar, "Sliding mode control of brushless DC motor speed with chattering reduction," 2015 IEEE 24th International Symposium on Industrial Electronics (ISIE), pp. 542-547, 2015, https://doi.org/10.1109/ISIE.2015.7281525.
[11] A. A. Tabassum, H. M. Cho, M. I. Mahmud, “Essential features and torque minimization techniques for brushless direct current motor controllers in electric vehicles,” Energies, vol. 17, no. 18, p. 4562, 2024, https://doi.org/10.3390/en17184562.
[12] C. Yanarates and Z. Zhou, "Design and Cascade PI Controller-Based Robust Model Reference Adaptive Control of DC-DC Boost Converter," IEEE Access, vol. 10, pp. 44909-44922, 2022, https://doi.org/10.1109/ACCESS.2022.3169591.
[13] J. M. Sosa, P. R. Martínez-Rodríguez, G. Vázquez and J. C. Nava-Cruz, "Control design of a cascade boost converter based on the averaged model," 2013 IEEE International Autumn Meeting on Power Electronics and Computing (ROPEC), pp. 1-6, 2013, https://doi.org/10.1109/ROPEC.2013.6702718.
[14] C. H. B. Apribowo, M. Ahmad, H. Maghfiroh, "Fuzzy logic controller and its application in brushless DC motor (BLDC) in electric vehicle-a review," Journal of Electrical, Electronic, Information, and Communication Technology, vol. 3, no. 1, pp. 35-43, 2021, https://doi.org/10.20961/jeeict.3.1.50651
[15] Y. I. M. A. Mashhadany, A. K. Abbas, and S. S. Algburi, "Modeling and analysis of brushless DC motor system based on intelligent controllers," Bulletin of Electrical Engineering and Informatics, vol. 11, no. 6, pp. 2995-3003, 2022, https://doi.org/10.11591/eei.v11i6.4365.
[16] A. L. Saleh, A. A. Obed, "Speed control of brushless DC motor based on fractional order PID controller," International Journal of Computer Applications, vol. 95, no. 4, pp. 1-6, 2014, https://doi.org/10.5120/16579-6269.
[17] H. S. Dakheel, Z. B. Abdullah, S. W. Shneen, "Advanced optimal GA-PID controller for BLDC motor," Bulletin of Electrical Engineering and Informatics, vol. 12, no. 4, pp. 2077-2086, 2023, https://doi.org/10.11591/eei.v12i4.4649.
[18] Z. B. Abdullah, S. W. Shneen, H. S. Dakheel, "Simulation model of PID controller for DC servo motor at variable and constant speed by using MATLAB," Journal of Robotics and Control (JRC), vol. 4, no. 1 pp. 54-59, 2023, https://doi.org/10.18196/jrc.v4i1.15866.
[19] L. Xu, J. Song and Q. Lin, "Brushless DC motor speed control system Simulink simulation," 2016 IEEE International Conference on Power and Renewable Energy (ICPRE), pp. 62-66, 2016, https://doi.org/10.1109/ICPRE.2016.7871173.
[20] H. S. Dakheel, Z. B. Abdullah, N. S. Jasim, S. W. Shneen, “Simulation model of ANN and PID controller for direct current servo motor by using Matlab/Simulink," TELKOMNIKA (Telecommunication Computing Electronics and Control), vol. 20, no. 4, pp. 922-932, 2022, http://doi.org/10.12928/telkomnika.v20i4.23248.
[21] E. Can, and H. H. Sayan, "The performance of the DC motor by the PID controlling PWM DC-DC boost converter," Tehnički glasnik, vol. 11, no. 4, pp. 182-187, 2017, https://hrcak.srce.hr/file/281593.
[22] G. A. Aziz, S. W. Shneen, F. N. Abdullah, D. H. Shaker, "Advanced optimal GWO-PID controller for DC motor," International Journal of Advances in Applied Sciences, vol. 11, no. 3, pp. 263-276, 2022, http://doi.org/10.11591/ijaas.v11.i3.pp263-276.
[23] S. N. Al-Bargothi, G. M. Qaryouti, and Q. M. Jaber, "Speed control of DC motor using conventional and adaptive PID controllers," Indonesian Journal of Electrical Engineering and Computer Science, vol. 16, no. 3, pp. 1221-1228, 2019, http://doi.org/10.11591/ijeecs.v16.i3.pp1221-1228.
[24] S. J. Hammoodi, K. S. Flayyih, and A. R. Hamad, "Design and implementation speed control system of DC motor based on PID control and Matlab Simulink," International Journal of Power Electronics and Drive Systems, vol. 11, no. 1, pp. 127-134, 2020, http://doi.org/10.11591/ijpeds.v11.i1.pp127-134.
[25] A. M. Ahmed, A. Ali-Eldin, M. S. Elksasy, F. F. Areed, “Brushless DC motor speed control using both PI controller and fuzzy PI controller,” International Journal of Computer Applications, vol. 109, no. 10, pp. 29-35, 2015, https://doi.org/10.5120/19227-0933.
[26] B. T. V. Gopal, E. G. Shivakumar, “Design and simulation of neuro-fuzzy controller for indirect vector-controlled induction motor drive,” Data Analytics and Learning: Proceedings of DAL 2018, pp. 155-167, 2019, https://doi.org/10.1007/978-981-13-2514-4_14.
[27] N. Tiwari, R. Diwan, “Speed Control of Brushless DC Motor using Fuzzy and Neuro-Fuzzy,” International Journal of Digital Application & Contemporary research, vol. 3, no. 6, 2015, https://ijdacr.com/uploads/papers/NT.pdf.
[28] A. Myrtellari, P. Marango, and M. Gjonaj, "Optimal control of DC motors using PSO algorithm for tuning PID controller,” UBT International Conference, pp. 15-22, 2015, https://doi.org/10.33107/ubt-ic.2015.40.
[29] R. Shanmugasundram, K. M. Zakariah and N. Yadaiah, "Implementation and Performance Analysis of Digital Controllers for Brushless DC Motor Drives," IEEE/ASME Transactions on Mechatronics, vol. 19, no. 1, pp. 213-224, 2014, https://doi.org/10.1109/TMECH.2012.2226469.
[30] H. S. Hameed, "Brushless DC motor controller design using MATLAB applications," 2018 1st International Scientific Conference of Engineering Sciences - 3rd Scientific Conference of Engineering Science (ISCES), pp. 44-49, 2018, https://doi.org/10.1109/ISCES.2018.8340526.
[31] J. Sriram and K. Sureshkumar, "Speed control of BLDC motor using fuzzy logic controller based on sensorless technique," 2014 International Conference on Green Computing Communication and Electrical Engineering (ICGCCEE), pp. 1-6, 2014, https://doi.org/10.1109/ICGCCEE.2014.6922466.
[32] Y. -K. Lin and Y. -S. Lai, "Pulsewidth Modulation Technique for BLDCM Drives to Reduce Commutation Torque Ripple Without Calculation of Commutation Time," IEEE Transactions on Industry Applications, vol. 47, no. 4, pp. 1786-1793, 2011, https://doi.org/10.1109/TIA.2011.2155612.
[33] A. Ramya, M. Balaji, V. Kamaraj, “Adaptive MF tuned fuzzy logic speed controller for BLDC motor drive using ANN and PSO technique,” The Journal of Engineering, vol. 2019, no. 17, pp. 3947-3950, 2019, https://doi.org/10.1049/joe.2018.8179.
[34] B. Terzic and M. Jadric, "Design and implementation of the extended Kalman filter for the speed and rotor position estimation of brushless DC motor," IEEE Transactions on Industrial Electronics, vol. 48, no. 6, pp. 1065-1073, 2001, https://doi.org/10.1109/41.969385.
[35] K. Xia, Y. Ye, J. Ni, Y. Wang and P. Xu, "Model Predictive Control Method of Torque Ripple Reduction for BLDC Motor," IEEE Transactions on Magnetics, vol. 56, no. 1, pp. 1-6, 2020, https://doi.org/10.1109/TMAG.2019.2950953.
[36] P. Suganthi, S. Nagapavithra and S. Umamaheswari, "Modeling and simulation of closed loop speed control for BLDC motor," 2017 Conference on Emerging Devices and Smart Systems (ICEDSS), pp. 229-233, 2017, https://doi.org/10.1109/ICEDSS.2017.8073686.
[37] H. Jigang, F. Hui, W. Jie, “A PI controller optimized with modified differential evolution algorithm for speed control of BLDC motor,” Automatika: Journal for Control, Measurement, Electronics, Computing and Communications, vol. 60, no. 2, pp. 135-148, 2019, https://doi.org/10.1080/00051144.2019.1596014.
[38] H. -C. Wu, M. -Y. Wen and C. -C. Wong, "Speed control of BLDC motors using hall effect sensors based on DSP," 2016 International Conference on System Science and Engineering (ICSSE), pp. 1-4, 2016, https://doi.org/10.1109/ICSSE.2016.7551633.
[39] A. Mamadapur and G. Unde Mahadev, "Speed Control of BLDC Motor Using Neural Network Controller and PID Controller," 2019 2nd International Conference on Power and Embedded Drive Control (ICPEDC), pp. 146-151, 2019, https://doi.org/10.1109/ICPEDC47771.2019.9036695.
[40] I. Anshory, D. Hadidjaja, I. Sulistiyowati, “Measurement, modeling, and optimization speed control of BLDC motor using fuzzy-PSO based algorithm,” Journal of Electrical Technology UMY, vol. 5, no. 1, pp. 17-25, 2021, https://doi.org/10.18196/jet.v5i1.12113.
[41] M. Wang, S. Chen, C. Shih, “Speed control of brushless DC motor by adaptive network-based fuzzy inference,” Microsystem Technology, vol. 24, pp. 33-39, 2018, https://doi.org/10.1007/s00542-016-3148-0.
[42] R. Yadav, M. K. Kar, A. K. Singh, “Speed control of a three-phase IM with closed-loop control scheme,” Recent Advances in Power Electronics and Drives, pp. 43-55, 2022, https://doi.org/10.1007/978-981-16-9239-0_4.
[43] R. Yadav, M. K. Kar and A. K. Singh, "Controlling Speed of a Permanent Magnet Synchronous Machine using Closed Loop Control Scheme," 2021 Emerging Trends in Industry 4.0 (ETI 4.0), pp. 1-6, 2021, https://doi.org/10.1109/ETI4.051663.2021.9619448.
[44] A. H. Ahmed, A. E. S. B. Kotb and A. M. Ali, “Comparison between Fuzzy Logic and PI Control for the Speed of BLDC Motor,” International Journal of Power Electronics and Drive System (IJPEDS), vol. 9, no. 3, pp. 1116-1123, 2018, http://doi.org/10.11591/ijpeds.v9.i3.pp1116-1123.
[45] M. Nasri, H. Nezamabadi-Pour, and M. Maghfoori, “A PSO-based optimum design of PID controller for a linear brushless DC motor,” International Journal of Electrical, Computer, Energetic, Electronic and Communication Engineering, vol. 26, no.40, pp. 211- 215, 2007, https://www.scirp.org/reference/referencespapers?referenceid=1830478.
[46] A. F. Al-Saoudi, K. M. Al-Aubidy and A. J. Al-Mahasneh, "Comparison of PID, Fuzzy Logic, ANFIS and Model Predictive Controllers for Cruise Control System," 2024 21st International Multi-Conference on Systems, Signals & Devices (SSD), pp. 263-265, 2024, https://doi.org/10.1109/SSD61670.2024.10548200.
[47] M. S. Hasan, A. F. Sharaf, M. D. Albakhait, A. I. Jaber, “High performance rectifier/multilevel inverter based BLDC motor drive with PI controller,” IOP Conference Series: Materials Science and Engineering, vol. 745, no. 1, p. 012005, 2020, https://doi.org/10.1088/1757-899X/745/1/012005.
[48] C. O. Omeje, A. O. Salau, “Torque ripples enhancement of a PMBLDC motor propelled through quadratic DC–DC boost converter at varying load,” ISA transactions, vol. 143, pp. 385-397, 2023, https://doi.org/10.1016/j.isatra.2023.08.027.
[49] M. K. Kar, S. S. Waghmare, S. Mujawar, S. Vadi, “Speed Control of a Brushless DC Motor Using Hall Sensor,”Recent Advances in Power Electronics and Drives, pp. 77-88, 2024, https://doi.org/10.1007/978-981-99-9439-7_7.
[50] P. Zhuang and H. Liang, "Hierarchical and Decentralized Stochastic Energy Management for Smart Distribution Systems With High BESS Penetration," IEEE Transactions on Smart Grid, vol. 10, no. 6, pp. 6516-6527, 2019, https://doi.org/10.1109/TSG.2019.2906823.
[51] S. Usha, P. M. Dubey, R. Ramya, M. V. Suganyadevi, "Performance enhancement of BLDC motor using PID controller," International Journal of Power Electronics and Drive Systems, vol. 12, no. 3, pp. 1335-1344, 2021, http://doi.org/10.11591/ijpeds.v12.i3.pp1335-1344.
[52] G. G. R. Sekhar and B. Banakara, “Performance of Brushless DC Drive with Single Current Sensor Fed from PV with High Voltage-Gain DC-DC Converter,” International Journal of Power Electronics and Drive System (IJPEDS), vol. 9, no. 1, pp. 33-45, 2018, http://doi.org/10.11591/ijpeds.v9.i1.pp33-45.
[53] S. W. Shneen, Z. B. Abdullah, and H. S. Dakheel, "Design and Implementation of Voltage Source Inverter Using Sinusoidal Pulse Width Modulation Technique to Drive A Single-Phase Induction Motor," International Journal of Robotics and Control Systems, vol. 4, no. 4, pp. 1527-1546, 2024, https://doi.org/10.31763/ijrcs.v4i3.1541.
[54] W. N. A. Abed, O. A. Imran, A. N. Abdullah, "Sensored speed control of brushless DC motor based salp swarm algorithm," International Journal of Electrical and Computer Engineering (IJECE), vol. 12, no. 5, pp. 4832-4840, 2022, http://doi.org/10.11591/ijece.v12i5.pp4832-4840.
[55] S. W. Shneen, A. L. Shuraiji, "Simulation model for pulse width modulation-voltage source inverter of three-phase induction motor," International Journal of Power Electronics and Drive Systems, vol. 14, no. 2, pp. 719-726, 2023, http://doi.org/10.11591/ijpeds.v14.i2.pp719-726.
[56] S. W. Shneen, G. A. Aziz, F. N. Abdullah, D. H. Shaker, "Simulation model of 1-phase pulse-width modulation rectifier by using MATLAB/Simulink," International Journal of Advances in Applied Sciences, vol. 11, no. 3, pp. 253-262, 2022, http://doi.org/10.11591/ijaas.v11.i3.pp253-262.
[57] S. W. Shneen, "Advanced optimal for power-electronic systems for the grid integration of energy sources," Indonesian Journal of Electrical Engineering and Computer Science, vol. 1, no. 3, pp. 543-555, 2016, http://doi.org/10.11591/ijeecs.v1.i3.pp543-555.
[58] Z. A. Al-Dabbagh, and S. W. Shneen, "Neuro-Fuzzy Controller for a Non-Linear Power Electronic DC-DC Boost Converters," Journal of Robotics and Control (JRC), vol. 5, no. 5, pp. 1479-1491, 2024, https://doi.org/10.18196/jrc.v5i5.22690.
[59] Z. A. Al-Dabbagh, S. W. Shneen, and A. O. Hanfesh, "Fuzzy Logic-based PI Controller with PWM for Buck-Boost Converter,” Journal of Fuzzy Systems and Control, vol. 2, no. 3, pp. 147-159, 2024, https://doi.org/10.59247/jfsc.v2i3.239.
Refbacks
- There are currently no refbacks.
Copyright (c) 2024 zainab ameer shaker, salam waley shneen
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
About the Journal | Journal Policies | Author | Information |
International Journal of Robotics and Control Systems
e-ISSN: 2775-2658
Website: https://pubs2.ascee.org/index.php/IJRCS
Email: ijrcs@ascee.org
Organized by: Association for Scientific Computing Electronics and Engineering (ASCEE), Peneliti Teknologi Teknik Indonesia, Department of Electrical Engineering, Universitas Ahmad Dahlan and Kuliah Teknik Elektro
Published by: Association for Scientific Computing Electronics and Engineering (ASCEE)
Office: Jalan Janti, Karangjambe 130B, Banguntapan, Bantul, Daerah Istimewa Yogyakarta, Indonesia